Woodland Scenics ST1463 O Scale Track-Bed Strips (36)

Strips are the perfect roadbed for tight track applications. They align well with cork or Homasote*. Track-Bed deadens sound, requires no pre-soaking like cork, remains flexible and will not dry out or become brittle. Saves over purchasing items separately. Install easily with Foam Tack Glue (ST1444). Pin in place with Foam Nails (ST1432) 36 strips/pkg- 3/16" D x 2 3/4" W x 24" L (5 mm x 6.98 cm x 60.9 cm). I am wondering why the O scale Track-Bed is wider than the foam inclines and risers. Am I missing something? When modeling in O scale, Inclines and Risers need to be placed side-by-side to double their width. I am interested in your Track-Bed. Is it black, dark gray or light gray? The Track-Bed is a dark gray. What is the best way to attach Track-Bed? For a strong bond, rough-up the bottom of Track-Bed with 80-grit sandpaper and attach using the contact method, working in small, manageable sections. Contact Method - Apply Foam Tack Glue to both surfaces, allow to set for approximately 20 minutes, but no longer than 1 hour, until tacky, then apply. What is the best method for laying out Track-Bed for placement on my layout? Lay out Track-Bed in one piece. Accommodate tight curves by separating the Track-Bed into two narrow strips along the slit that runs lengthwise. Lay the two pieces seperately, butting them snuggly in the middle. Do this by first drawing a center line for your track. Lay each half strip of Track-Bed on either side along this center line. Can I use a Hot Wire Foam Cutter to cut my Track-Bed? No, do not cut the Track-Bed with a Hot Wire Foam Cutter. This may emit toxic fumes. Is the Track-Bed solvent resistant? Yes, Track-Bed is solvent resistant. Why is Track-Bed better than cork? Track-Bed absorbs the noise and vibration of train operations, so you can enjoy the true "clickety-clack" sound. Track-Bed costs less, does not require pre-soaking, and is easy to apply. It will not dry out, crack and crumble like cork. Since Track-Bed is compatible and aligns easily with cork, you can update your cork bed at any time. I am using Track-Bed, and securing the track with Foam Tack Glue. Now, I need to move one of the tracks. How can I get the Foam Tack Glue to release? To remove Track-Bed, soften the Foam Tack Glue with warm, soapy water. If the glue is hard to remove, use denature alcohol. How much Foam Tack Glue will I need when I lay my Track-Bed? N scale Track-Bed - 1/3 oz of Foam Tack Glue covers approximately 4 feet of N scale Track-Bed HO scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 2 feet of HO scale Track-Bed O scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 1 foot of O scale Track-Bed Super Sheets - 1 oz per Super Sheet. 1 bottle (12 fl oz) will do 12 Super Sheets. NOTE: Coverage is approximate. Exact coverage depends on thickness of application. Can your Track-Bed be used with any brand of track and on any layout? Yes, our Track-Bed works great on any type layout with any kind of track of a standard width. For larger scales, consider using Track-Bed Sheets. Is it easier to use the rolls of Track-Bed or the strips? It really is the users preference, both are easy to use. Generally speaking, Track-Bed Rolls are easier to use when modeling a larger layout with a lot of straightaways and standard curves. Track-Bed Strips are easier to use when modeling a smaller layout with a lot of sharp curves and turnouts. After I have glued the Track-Bed to my table top and it dries, can I use plastic screws to further secure my track to the Track-Bed? We do not manufacture plastic screws and have never tested their usage. This is how we recommend you attach track to your Track-Bed. We recommend using Foam Tack Glue. Sand surface of Track-Bed with 120-grit sandpaper, then spread a thin layer of glue over the Track-Bed surface and install track. Pin in place with Foam Nails while drying. How do I attach Track and Track-Bed to my layout? We recommend using Foam Tack Glue to attach Track-Bed and Track to a layout. There are different application methods for attaching Track-Bed to your layout depending on the base material. Plaster surfaces: Spread a thin, even layer of Foam Tack Glue where Track-Bed will be installed. Lay Track-Bed and pin in place with Foam Nails to secure while drying. Work in two to three-foot sections. This application method also allows the modeler to make adjustments while installing Track-Bed. A permanent application method for plaster and other surfaces: Use the Contact Gluing Method. Apply Foam Tack Glue to both contact surfaces. Let dry until clear and tacky (maximum working time is 1 hour), and then press Track-Bed in place. Installation of Track-Bed has to be precise, because glue will bond instantly. Place Track-Bed in manageable sections. For both application methods, we recommend sanding the top and bottom surface of Track-Bed with 120-grit sandpaper before installation. To attach your track to the Track-Bed, spread a thin, even layer of Foam Tack Glue on top of the Track-Bed. Place pieces of track on glue and pin in place with Foam Nails to secure while drying. I am having a problem with the ballast adhering to the Track-Bed. You should have no problem adhering Ballast to your Track-Bed with this tested method. 1. Pour Ballast over track. Brush from rails and tops of ties. 2. Mist with Scenic Cement to wet the surface, and then saturate Ballast using an eyedropper or Scenic Sprayer. 3. Clean rails before use. What adhesive is the most suitable for securing Woodland Scenics trackbed to a painted or unpainted plywood surface? We recommend using Foam Tack Glue to adhere Track-Bed to a plywood base. If the plywood is painted, we suggest that you use 80 or 100 grit sandpaper to rough up the surface. This will give a tooth for the adhesive to hold on to. If the plywood isn't painted, you do not have to do this. To attach Track-Bed to a plywood base, use the contact gluing method. Apply adhesive to both contact surfaces and let dry until clear and tacky (maximum working time is one hour). When installing Track-Bed, the glue will bond instantly. What is the minimum radius for N, HO and O scale Track-Bed? The minimum turn radius for: N scale 9 1/2" - 9 3/4" HO scale 15" O scale 27" How do I apply track-bed along curves? Separate Track-Bed into two sections along the score line. Draw a centerline along the curve. Using the centerline as a guide, press Track-Bed sections in place separately, butting them snugly side-by-side. We recommend attaching Track-Bed with Foam Tack Glue.